Extrusion Pelletizing Lines

Showing all 7 results

  • 4.5″ PTI Vented -32:1 Extrusion Pelletizing Line – New 2022

    Category: Extrusion Pelletizing Lines

    ITEM #: 12990Read more

    4.5″ PTI 32:1 Vented – Air Cooled Extrusion Pelletizing Line – New 2022

    Model Apex Series

    Vented Barrel and Two Stage Screw

    Air Cooled

    Screw Speed 125 RPM

    Emerson 200 HP DC Motor – Rebuilt 2012

    ABB Drive 300 HP Drive purchased and installed in 2012

    PTI Control Cabinet with 6 barrel zones, 3 die zones, 3 screen changer zones

    Center Height: 59″ – Die discharge heignt 48″

    Strand Die 30 Hole

    14″ width air knife new 2012

    Tec Polymer Water Bath – stainless steel – built new 2012, 14″ length x 24″ width

    Cumberland Pelletizer Model 6 – 8 knife bolt on rotor – Drive- AC Tech Ac Inverter Drive

    Mounted on casters

    New Classifier – New 2012 – 28″ Two Stage Classifier, four (4) Deck, 10 mesh, 1/4″ holes for overs, 1 HP motor 230/460 volt

    Foremost Crammer Feeder – 4.5″ diameter Foremost crammer feeder complete with Formost variable speed control panel.

  • 6″ Davis Standard Pelletizing Line

    Category: Extrusion Pelletizing Lines

    ITEM #: 12916Read more

    Used 6″ Davis standard Egan / Berringer water ring pelletizing line consisting of:
    6″ Davis Standard Egan extruder, model 6026-D.R.H, 44:1 l/d, electrically heated,
    water cooled barrel, jacketed feed section, vented barrel with vacuum pump,
    11.478:1 gearbox ratio, with 400 hp dc motor, cored screw, control panel, gearbox
    serial# X4506, Nordson hydraulic slide plate screen changer with power pack,
    Berringer water ring pelletizer, model WRP36, driven by 7.5 hp motor, stainless
    steel water box and dewatering trough, with Gala 600 gpm, tempered water
    system, model PWT600, stainless steel heat water basin, model 52VDW Gala
    spin dryer, with diverter valve, and Gala Fines sieve, with circulation pump, and
    cartridge filters

  • Davis Standard Used 4.5″ Ram Stuffing Cascade Pelletizing Line, Xaloy Water Ring Pelletizer – New  2006

    Category: Extrusion Pelletizing Lines

    ITEM #: 12813Read more

    Davis Standard Used 4.5″ Ram Stuffing Cascade Pelletizing Line, Xaloy Water Ring Pelletizer – New  2006

    – Water Cooled Barrel, 11.68 Gearbox Ratio, 400hp Gearbox Capacity with 1.25 Service Factor

    – 300hp Baldor Inverter Duty Direct Drive Motor, 1790rpm, Yaskawa AC Drive

    -Secondary Dump Davis Standard Single Screw Extruder, Model 45IN35, New in 2006
    – Water Cooled Barrel, 250hp Capacity with 1.25 Service Factor
    – 100hp Marathon Blue Max AC Motor, Yaskawa AC Drive
    – Plasticolor 3000 Dual Additive Feeder
    – Xaloy WRP-12i Water Ring Pelletizer, 3hp Cutting Head
    – Table Style Pellet Classifier
    – Allen Bradley PanelView Plus 1500 Touch Screen Control Panel
    Previously Running 1,000 lbs/hr of PP film
  • NGR X GRAN 165 RECYCLING LINE

    Category: Extrusion Pelletizing Lines

    ITEM #: 12430Read more

    NGR X GRAN 165

    Material that can be processed: PE, PP, LDPE, HDPE, MDPE

    Screw Diameter: 165 mm

    Output: Up to 1200 KG./Hour

    L/D Ratio:  40:1

    Screen Changer: XALOY EH80 HYDRAULIC SCREEN CHANGER

    Presure Sensor:  4000 PSI, MPI

    Conveyor Belt: Contains 2 – High Bonmded Heavy Duty Cleats

    Degassing: DOUBLE DEGASSING

    Power: 575 V 3 Phase for motor – 480 v – 3 phase down stream

    Further Information:

    Extruder motor 370 KW

    CUTTER-COMPACTOR MOTOR 132 KW

    FEED SCREW 45 KW

    VACUUM PUMPS 15 KKW

    DRYER MOTORS 13 KW

    HEATING BARREL ZONES 12

    AIR COOLED

  • EREMA INTAREMA 1512-TVE Plus Pelletizing Line – New 2018

    Category: Erema Recycling Lines

    ITEM #: 12400Read more

    Erema Intarema 1512_TVEplus Pelletizing Line Used Erema Intarema 1512_TVEplus Pelletizing Line, nominal capacity range 850-1250kg/hr depending on feed material, currently with 8505 run hours consisting of the following: -FB_7000_1100_SH cleated feed conveyor, 1100mm(43″) wide x 7000mm(275″) long cleated inclined belt. -DTF 1300/1100/400 pass thru over belt metal detector, 400mm(15.7″) tall opening. -Erema Intarema extruder, model I_1521_TVEplus with ecoSave, preconditioning densifier, with 4 blade rotor, under driven by 250kw(335hp) ac motor, single screw melt extruder, 3S technology mixing, driven by 250kw(335HP) ac motor. -powder exhaust system with cyclone collector and blower for preconditioning densifier -LF_2_354 laser filter, 1295 sq cm filter area, scraper driven by 4kw motor drive on stand. -dual side degassing vents with 4.3kw liquid ring vacuum pump system with water circulation system, pump, and stainless steel water basin. -HG_244D hot die face pelletizer driven by 2.2kw(2.9HP) ac motor with (5) blade cutting head, stainless steel water ring housing with water pump station with heat exchanger and circulation pump. -GS_2010_1000 pellet dewater screen, stainless steel screen deck, driven by dual .30kw vibro motor with water catch basin. -GZ_1000_M15 centrifugal pellet dryer, 500mm(19.6″) diameter driven by 22kw(29.5HP) ac motor pellet transport system with cyclone collector with rotary air lock and blower. -integrated EL_Smart operator hmi control station, control panels with PLC controls, and extruder motor frequency controllers. system serial# P-20170340, built 2018

  • 6″ NRM COMPLETE STRAND PELLETIZING LINE – OUTSTANDING PRICE !!!!

    Category: Extrusion Pelletizing Lines

    ITEM #: 12389Read more

    6″ NRM Model PM 70 – Strand Pelletizing Line with open vent with pressure gauge and rupture disc. Two Stage Screw. Main Control Panel. Long gated Feed Section.
    125 HP AC Motor and Drive with Drive rated 125 HP – 150 HP. Drive in separate Control Panel. Color Feeder mounted on bottom of hopper.
    21 Strand Die 45 Degree angle with 6″Screen Changer with Power Pack.
    Material Run, PE and Pro. Crate full of Spare Screen Packs for Extruder.
    Stainless Steel Water Bath 16 1/2″ wide x 10″ deep x 25 feet long with Vacuum Systen to remove water from strands.
    20 Ton Air Cooled Chiller. Reiter Pelletier – Stainless Steel Shaker Table 25″ wide x 72″long. Auger out of Shaker Table to Gaylord Discharge.
    VIDEO IS AVAILABLE UPON REQUEST.

  • NGR X GRAN 165 RECYCLING LINE- New 2009

    Category: Extrusion Pelletizing Lines

    ITEM #: 11014Read more

    NGR X GRAN 165 Recycling Line – New 2009

    Material that can be processed: PE, PP, LDPE, HDPE, MDPE